#Timetool for tasco trail camera install
#Timetool for tasco trail camera full

Users will likely want to setup the camera at home, in advance. While this can be done in the field (no computer or internet access is needed), most Once batteries are installed and an SD card is inserted, you’re ready to go into the Setup Mode to get the camera ready to use, with all options set to your preferences. Be sure the camera’s power is switched OFF before removing or inserting SD cards. The card is released from the slot and ready to be removed when you hear the click.

To take out the SD card, just gently push in the card (do not try to pull it out without pushing in first).

You have backed up (saved to your computer) any files you want to keep on a previously used card, as formatting erases ALL files. This can be done using the camera’s “Format” function (pg.

Formatting the SD card before using it for the first time is recommended, especially when a card has been used in other devices.

“Err” means there is a card reading error (try a different SD card). Memory is full, with no remaining room to store files (see below). Other card status display messages: “FULL” indicates the card’s

If the SD card is not inserted correctly, or no card is in the slot, “Card” will appear on the LCD Display, and the camera will not operate (Fig.

If the wrong side of the card is facing up, you will not be able to insert it without force-there is only one correct way to insert cards. With the power switch in the OFF position, insert the SD card in the slot on the lower right side of the camera (Fig.

Make sure that the write-protect switch on the side of the card is “off” (NOT in the “Lock” position).

SD and SDHC (High Capacity) class 4 or higher speed cards, up to a maximum 32GB are supported. The Tasco Trail Camera uses a standard SD (Secure Digital) memory card to save your photos (.jpg format) or videos (.avi format). NiMh Rechargeable batteries can also be used, but they might have a shorter life span due to their reduced efficiency over time and at low temperature. Tasco recommends using eight new lithium AA (Energizer® brand) or alkaline AA batteries.

#Timetool for tasco trail camera full

The camera is capable of operating with only 4 batteries installed if necessary, but a full set of 8 batteries should normally be used to ensure the longest operating time. Indications at the bottom of the battery tray. Be sure to insert each battery so its polarity (+/- direction) matches the polarity Switch the camera’s power OFF when loading/unloading batteries. Press the Battery Tray Eject Button to release the battery tray and pull it out for loading (Fig. Of, so please take the time to read the following directions and cautions: Loading Batteries Although that may only take you a minute, there are some important notes about both batteries and SD cards you should be aware

#Timetool for tasco trail camera install

1īefore you begin to use your Tasco Trail Camera, you will first need to install a set of batteries and insert an SD card. Once you setup the camera, switch it to ON for normal operation. The Up, Down and OK keys are used to set the date and time (to be imprinted on each photo/video), change the interval or “detection delay” time between images while an animal remains in range of the camera’s sensor, select Photo or Video capture mode, set a camera ID number for your reference, and format the SD card (erase all files). The LCD Display will show the camera’s current settings in Setup Mode. The AIM position can also be used to verify the area the camera will monitor. When the power switch is set to the AIM middle position, the camera is in Setup Mode.

A 3-way power/mode switch is used to select the main operating modes: OFF, AIM, and ON (Fig. Release the two latches on the right side of the camera and swing the front cover over to the left to access the controls. The Tasco Trail Camera is designed for outdoor use and is water resistant. The Tasco Trail Camera is equipped with built-in infrared (IR) LEDs that function as a flash, so that it delivers clear photos or videos (in black & white) even in the dark, and it can take color photos or videos under sufficient daylight. Once motion in the monitored area is detected, the digital camera unit will be triggered at once (typically less than 1 second) and then automatically take photos or videos (your choice). This means it can deliver up to six months stand-by operation time when the device is powered by eight AA alkaline batteries, and up to twelve months utilizing eight lithium AA batteries (30 images per day, 15 w/flash). The Tasco Trail Camera consumes very little power (< 0.5mA) in a stand-by (surveillance) state. Or 8MP resolution, depending on model), or video clips (720p, 10 seconds length). It can be triggered by any movement of live animals in a location, detected by a highly sensitive Passive Infra-Red (PIR) motion sensor, and then take high quality photos (6MP Your new Tasco® Trail Camera is a digital scouting camera.